-
Fototrend
Az alábbi téma IT szakmai jellegű kérdezz-felelek topik. Megkérünk benneteket, hogy a nem szakmai kérdéseket az Azonnali (fáradt gőzös) kérdések topikjában tegyétek fel.
Új hozzászólás Aktív témák
-
calf
tag
BIOS microcod nélkül is viszi a Xeonokat, a P43-ba sincs Mod Bios.
Amelyik lap lekezeli a Q9550 illetve Q9650-et az jo.ha microcode kellene neki sztem ismeretlenként jönne be( pl p5b), viszont itt se kép se hang és a legnagyobb cumi, h a régi procival se....
Telefonos Ügyfélszolgálatom 0-24!! +36 HETVEN /394-6ÖT-3HAT Ha több pirosad van mint nekem előre utalok!
-
pocokxx
Közösségépítő
Megpróbálhatod, elvileg van ilyen funkció a lapon, és remélhetőleg ugyanúgy működik, minden Fujinál. [link]
If a severe error such as a power failure occurs while the BIOS update is in progress, the BIOS may become
corrupted and leave the system in an unbootable condition. The Fujitsu Technology Solutions Recovery BIOS
technology allows the repair of the BIOS; a new BIOS can be flashed from a floppy disk or a USB Memory Stick
any time, thereby restoring the functionality.
The Recovery BIOS resides in its own area in the Flash EEPROM; it is well protected from corruption and
available even after a disastrous flashing attempt. If required, use the following method to recover the BIOS:
1. Turn off the computer, disconnect the A/C power cable and open the case
2. According to your type of mainboard, set jumper to: “Enable System BIOS recovery”; see table
below for the jumper settings
3. Close the chassis, reconnect the A/C cable
4. Insert a BIOS Update diskette (see section “How to update the BIOS?”) or an USB Memory Stick
and turn the computer on
5. Watch the sounds from the system speaker
The BIOS recovery was successful when you hear beeps in the sequence ”short-short-long-longlong”
and the floppy activity light turns off. The BIOS recovery may take a few minutes.
6. Turn off the computer, disconnect the AC cable and open the chassis
7. Reset the jumpers to their original position
8. Close the chassis, reconnect the A/C cable and remove the diskette or USB Memory Stick
9. Turn on the computer and enter the BIOS-Setup. (Press the <F2> key during Boot)
10. Select “Get Default Values” in the menu EXIT
11. In the menu “EXIT”, choose “Save Changes & Exit”
The computer will now reboot and the BIOS Recovery is complete.[ Szerkesztve ]
"Egyformának lenni mindenkihez. Emberfeletti nagy szív kell ehhez." - Reményik Sándor
Új hozzászólás Aktív témák
Kedves Fórumozók!
Az alábbi téma IT szakmai jellegű kérdezz-felelek topik. Megkérünk benneteket, hogy a nem szakmai kérdéseket az Azonnali fáradtgőzös kérdések topikjában tegyétek fel.
- Székesfehérvár és környéke adok-veszek-beszélgetek
- Mibe tegyem a megtakarításaimat?
- Android alkalmazások - szoftver kibeszélő topik
- Eredeti játékok OFF topik
- Xbox Series X|S
- Bemutatta első táblagépét saját neve alatt a HMD
- Megérkezett a Corsair új M.2-es SSD-je, és mindennek mondható, csak lassúnak nem
- EAFC 24
- bambano: Bambanő háza tája
- SkyShowtime
- További aktív témák...
Állásajánlatok
Cég: Ozeki Kft.
Város: Debrecen
Cég: Promenade Publishing House Kft.
Város: Budapest