Új hozzászólás Aktív témák

• #5772 ksanc őstag

  Új Válasz 2020-01-15 22:17:11 #5772

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  ksanc

  őstag

  JEEEEEE, megvan az UART... csk a szememet bökte ki, pedig már leszedtem az árnyékoló lemezt a prociról, ott figyelt alatta az RX TX tesztpont.
  Igen, elszáll a boot PANIC-al.

  Berakom a végét:

  [PART] partition hdr (1)
  [PART] Image with part header
  [PART] name : LK
  [PART] addr : FFFFFFFFh mode : -1
  [PART] size : 375188
  [PART] magic: 58881688h
  [PART] load "lk" from 0x0000000001DC0200 (dev) to 0x81E00000 (mem) [SUCCESS]
  [PART] load speed: 26170KB/s, 375188 bytes, 14ms
  bldr load items part
  [BLDR] items partition not found
  Battery exist
  [0xE]=0x5
  preloader items:items_get_secmem_start = 0x0
  preloader items:items_get_secmem_size = 0x200000
  preloader items:bootarg.lcm_name =
  preloader items:items_reserved_mem: 0x0000000000000000, 0x0000000000200000
  [PLF] boot to LK by ATAG.
  boot reason: 0
  boot mode: 0
  META COM0: 0
  rank[0] size 0x30000000
  rank[1] size 0x30000000
  tee resv mem 0x0000000000000000 0x0000000000000000
  md_type[0]: 0xFF
  md_type[1]: 0xFF
  boot time: 715
  DDR resv mode enable = 0, success = 0
  dram buf size 1691648
  SMC 0x0
  LK 0x3
  Kernel 0x3
  N-Sec SRAM Addr: 0x10DC00, size: 0x4000
  [BLDR] jump to 0x81E00000
  [BLDR] <0x81E00000>=0xEA000007
  [BLDR] <0x81E00004>=0xEA00542E
  [0] kernel_boot_opt=3
  [0] 32Bit Kernel
  [0] [LEDS]LK: leds_init: mt65xx_backlight_off
  [0] [LEDS]LK: mt65xx_backlight_off
  [0] [LEDS]LK: lcd-backlight level is 0
  [0] disp_pwm_level_remap backlight coefficient is -2115798972!!!
  [0] [pmic_init] LK Start..................
  [0] [pmic_init] MT6350 CHIP Code = 0x2050
  [0] [pmic_init] Done
  [10] ==LK info ==
  [20] Build time:Aug 29 2019, 11:49:18
  [20] chip_code[0x6580]
  [20] chip_ver[0x0]
  [20] ==LK info ==
  [20] ==dump boot argument==
  [20] BOOT_REASON: 0
  [20] BOOT_MODE: 0
  [20] META_COM TYPE: 0
  [20] META_COM ID: 0
  [20] META_COM PORT: 285233152
  [20] LOG_COM PORT: 285233152
  [20] LOG_COM BAUD: 921600
  [20] LOG_COM EN: 1
  [20] MEM_NUM: 2
  [20] MEM_SIZE: 0x30000000
  [20] MEM_SIZE: 0x30000000
  [20] mblock num: 0x2
  [20] mblock start: 0x80000000
  [20] mblock size: 0x30000000
  [20] mblock rank: 0x0
  [20] mblock start: 0xb0000000
  [20] mblock size: 0x30000000
  [20] mblock rank: 0x1
  [20] mblock start: 0x0
  [20] mblock size: 0x0
  [20] mblock rank: 0x0
  [20] mblock start: 0x0
  [20] mblock size: 0x0
  [20] mblock rank: 0x0
  [20] orig_dram num: 0x2
  [20] orig_dram start: 0x80000000
  [20] orig_dram size: 0x30000000
  [20] orig_dram start: 0xb0000000
  [20] orig_dram size: 0x30000000
  [20] orig_dram start: 0x0
  [40] orig_dram size: 0x0
  [40] orig_dram start: 0x0
  [40] orig_dram size: 0x0
  [40] lca start: 0x0
  [40] lca size: 0x0
  [40] tee start: 0x0
  [40] tee size: 0x0
  [40] MD_INFO: 0xff
  [40] MD_INFO: 0xff
  [40] MD_INFO: 0xff
  [40] MD_INFO: 0xff
  [40] BOOT_TIME: 715
  [40] DA_INFO: 0xffffffff
  [40] DA_INFO: 0xffffffff
  [40] DA_INFO: 0xffffffff
  [40] DA_INFO: 0xffffffff
  [40] DA_INFO: 0xffffffff
  [40] SEC_INFO: 0xffffffff
  [40] SEC_INFO: 0xffffffff
  [40] PART_NUM: 1
  [40] PART_INFO: 0x82058a04
  [40] EFLAG: 0
  [40] DDR_RESERVE: 0
  [40] DDR_RESERVE: 0
  [40] DRAM_BUF: 1691648
  [40] SMC: 0x0
  [40] SMC: 0x3
  [40] SMC: 0x3
  [40] SRAM satrt: 0x10dc00
  [40] SRAM size: 0x4000
  [40] ==dump boot argument==
  [40] platform_init()
  [40] [msdc_init]: msdc0 Host controller intialization start
  [40] [SD0] Pins mode(2), none(0), down(1), up(2), keep(3)
  [40] [SD0] Pins mode(1), none(0), down(1), up(2), keep(3)
  [60] [SD0] Pins mode(2), none(0), down(1), up(2), keep(3)
  [60] [info][msdc_config_clksrc] input clock is 208000kHz
  [60] [SD0] Bus Width: 1
  [60] [info][msdc_config_clksrc] input clock is 208000kHz
  [60] [SD0] SET_CLK(260kHz): SCLK(260kHz) MODE(0) DDR(0) DIV(200) DS(0) RS(0)
  [60] [msdc_init]: msdc0 Host controller intialization done
  [200] [info][msdc_config_clksrc] input clock is 208000kHz
  [200] [SD0] SET_CLK(260kHz): SCLK(260kHz) MODE(0) DDR(0) DIV(200) DS(0) RS(0)
  [200] [SD0] Bus Width: 8
  [200] [SD0] Switch to High-Speed mode!
  [220] [SD0] Size: 29600 MB, Max.Speed: 52000 kHz, blklen(512), nblks(60620800), ro(0)
  [220] [mmc_init_mem_card 3035][SD0] Initialized, eMMC50
  [220] before host->cur_bus_clk(260000)
  [220] [info][msdc_config_clksrc] input clock is 208000kHz
  [220] [SD0] SET_CLK(52000kHz): SCLK(52000kHz) MODE(0) DDR(0) DIV(1) DS(0) RS(0)
  [220] host->cur_bus_clk(52000000)
  [220] [mmc_init_card]: finish successfully
  [220] [mt_part_register_device]
  [220] [GPT_LK]Parsing Primary GPT now...
  [220] [GPT_LK][0]name=proinfo, part_id=8, start_sect=0x400, nr_sects=0x1800
  [220] [GPT_LK][1]name=nvram, part_id=8, start_sect=0x1c00, nr_sects=0x2800
  [240] [GPT_LK][2]name=protect1, part_id=8, start_sect=0x4400, nr_sects=0x5000
  [240] [GPT_LK][3]name=protect2, part_id=8, start_sect=0x9400, nr_sects=0x5000
  [240] [GPT_LK][4]name=seccfg, part_id=8, start_sect=0xe400, nr_sects=0x200
  [240] [GPT_LK][5]name=ITEMS, part_id=8, start_sect=0xe600, nr_sects=0x800
  [240] [GPT_LK][6]name=lk, part_id=8, start_sect=0xee00, nr_sects=0x300
  [240] [GPT_LK][7]name=boot, part_id=8, start_sect=0xf100, nr_sects=0x8000
  [240] [GPT_LK][8]name=recovery, part_id=8, start_sect=0x17100, nr_sects=0x8000
  [240] [GPT_LK][9]name=para, part_id=8, start_sect=0x1f100, nr_sects=0x400
  [240] [GPT_LK][10]name=logo, part_id=8, start_sect=0x1f500, nr_sects=0x4000
  [240] [GPT_LK][11]name=expdb, part_id=8, start_sect=0x23500, nr_sects=0x5000
  [240] [GPT_LK][12]name=frp, part_id=8, start_sect=0x28500, nr_sects=0x800
  [240] [GPT_LK][13]name=nvdata, part_id=8, start_sect=0x28d00, nr_sects=0x10000
  [260] [GPT_LK][14]name=metadata, part_id=8, start_sect=0x38d00, nr_sects=0x13300
  [260] [GPT_LK][15]name=oemkeystore, part_id=8, start_sect=0x4c000, nr_sects=0x1000
  [260] [GPT_LK][16]name=secro, part_id=8, start_sect=0x4d000, nr_sects=0x3000
  [260] [GPT_LK][17]name=keystore, part_id=8, start_sect=0x50000, nr_sects=0x4000
  [260] [GPT_LK][18]name=system, part_id=8, start_sect=0x54000, nr_sects=0x400000
  [260] [GPT_LK][19]name=cache, part_id=8, start_sect=0x454000, nr_sects=0x80000
  [260] [GPT_LK][20]name=userdata, part_id=8, start_sect=0x4d4000, nr_sects=0x34f3c00
  [260] [GPT_LK][21]name=flashinfo, part_id=8, start_sect=0x39c7c00, nr_sects=0x8000
  [260] [GPT_LK]Success to find valid GPT.
  [260] [PART_LK][get_part] para
  [LK_ENV]ENV SIG Wrong
  [LK_ENV]no valid env
  lk items:items_reserved_mem.start = 0x00000000
  lk items:items_reserved_mem.size = 0x00200000
  [280] [PART_LK][get_part] items
  lk items: ITEMS_START address = 0x00000000
  lk items:begin init.
  items_len=9 ,tail_char =
  truncated config items: 10
  --------items_len = 9
  0: čă čă
  1: čă čă
  2: čă čă
  3: čă čă
  4: čă čă
  5: čă čă
  6: čă čă
  7: čă čă
  8: čă čă
  9: čă čă
  10: čă čă
  11: čă
  [280] warning: size is not 2MB aligned
  [280] mblock[0].start: 0x80000000, sz: 0x30000000, limit: 0x100000000, max_addr: 0x0, max_rank: 1, target: -1, mblock[].rank: 0
  [300] mblock_reserve dbg[0]: 1, 1, 1, 1
  [300] mblock[1].start: 0xb0000000, sz: 0x30000000, limit: 0x100000000, max_addr: 0xb0000000, max_rank: 1, target: 0, mblock[].rank: 1
  [300] mblock_reserve dbg[1]: 1, 1, 1, 1
  [300] mblock_reserve: dff00000 - e0000000 from mblock 1
  [300] FB base = 0xdff00000, FB size = 1048576
  [300] fb_va: 0xdff00000, fb_pa: 0xdff00000, fb_pa_k: 0xdff00000
  [300] items found item_lcm_name =
  [LK_ENV]get_env DFO
  [300] panic (caller 0x81e1294b): ASSERT FAILED at (platform/mt6580/ddp_manager.c:518): dp_handle != NULL

  Egyébként ez a kijelzőkezeléshez tartozik, pont ugyanezt csinálja, ha lehúzom a szalagkábelét. Vagyis szereznem kellene egy ilyen kijelzőt tesztelésre

  Vaó, egyébként baromi izgi nézni, mit is csinál működés közben

Új hozzászólás Aktív témák