Új hozzászólás Aktív témák

• #7361 zodo nagyúr Vladi #7360

  Új Válasz 2009-03-08 12:41:07 #7361

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  zodo

  nagyúr

  válasz Vladi #7360 üzenetére

  Csomag telepítése megtörtént ,meg is találom a Usr/bin mappában,de újraíndítás útán semmi. A cikkben említett két sort ,nem tudtam hova beilleszteni.
  Megprobáltam ,amit a cikk végén ír,hogy nyomja le a Ctrl+Alt+backspace kombot,de szintén semmi.
  Megnéztem a Etc/Consol-tool mappában lévő Config fájl tartalmát.
  Ebben ennyit találtam:

  # This files tells the console-tools package:
  #
  # - whether to load a specific font and boot (and maybe a screen-font map,
  # but you should avoid that if possible).
  # - whether to setup an Application-Charset Map other than the default CP437.
  # - whether to start "vcstime" to have time on all text VC'S.
  #
  # You can also specify per-VC settings by suffixing variable names as in
  # the examples below. This only works on framebuffer devices.
  #
  # CAVEATS:
  #
  # - When using the new framebuffer devices, the "global setting" for a font
  # only affects the current console (ie., at boot-time, the first one)
  # - ACM setting involves 2 steps (maybe loading a user ACM, and activating
  # it on a given charset slot - see charset(1) for details), the 1st of which
  # affects the entire system, but the 2nd of which only affects the current
  # VC (ie., at boot-time, the first one). So that if you want to use the same
  # ACM on all VCs, you have to specify "APP_CHARSET_MAP_vc<N>=user" for all
  # relevant values of <N>.
  #
  # Example:
  #
  #SCREEN_FONT=iso01.f16
  #SCREEN_FONT_vc2=LatArCyrHeb-16
  #
  #APP_CHARSET_MAP=iso05
  #APP_CHARSET_MAP_vc2=user
  #
  # Set the following - more euro-friendly default than kernel font.
  # SCREEN_FONT=latarcyrheb-sun16.psf
  
  #DO_VCSTIME=yes
  #
  # Forget this one unless you _know_ it is necessary for your font:
  #SCREEN_FONT_MAP=iso01
  
  # **** screen saver/DPMS settings: all VCs ****
  # These settings are commented by default to avoid the chance of damage to
  # very old monitors that don't support DPMS signalling.
  
  # screen blanking timeout. monitor remains on, but the screen is cleared to
  # range: 0-60 min (0==never) kernels I've looked at default to 10 minutes.
  # (see linux/drivers/char/console.c)
  BLANK_TIME=30
  
  # blanking method (VESA DPMS mode to use after BLANK_TIME, before powerdown):
  # on: the default, no DPMS signalling. near instant powerup, no power saving
  # vsync: DPMS Standby mode. nearly instant recovery, uses 110/120W (17" screen)
  # hsync: DPMS Suspend mode. typically 3s recovery, uses 15/120W (17" screen)
  # powerdown,off: DPMS Off mode, typ. 10s recovery, uses 5/120W (17" screen)
  
  # Those values are for my 17" Mag, but some monitors do suspend the same as
  # standby. xset dpms force {off|standby|suspend|on} is useful for this, if X
  # supports DPMS on your video card. Set X's DPMS screensaver with xset dpms
  # or use option power_saver in XF86Config
  #
  # DPMS set by default to on, because hsync can cause problems on certain
  # hardware, such as Armada E500 laptops
  BLANK_DPMS=off
  
  # Powerdown time. The console will go to DPMS Off mode POWERDOWN_TIME
  # minutes _after_ blanking. (POWERDOWN_TIME + BLANK_TIME after the last input)
  POWERDOWN_TIME=30
  
  # rate and delay can get only specific values, consult kbdrate(1) for help
  #KEYBOARD_RATE="30"
  #KEYBOARD_DELAY="250"
  
  # Turn on numlock by default
  #LEDS=+num
  SCREEN_FONT=lat2-sun16
  SCREEN_FONT_vc2=lat2-sun16
  SCREEN_FONT_vc3=lat2-sun16
  SCREEN_FONT_vc4=lat2-sun16
  SCREEN_FONT_vc5=lat2-sun16
  SCREEN_FONT_vc6=lat2-sun16

Új hozzászólás Aktív témák