Új hozzászólás Aktív témák

• #8335 Toninho13 aktív tag Adamo_sx #8331

  Új Válasz 2018-10-26 12:46:55 #8335

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  Toninho13

  aktív tag

  válasz Adamo_sx #8331 üzenetére

  Hogy őszinte legyek, nem értem mi történik. Tvheadend admin felületén magától megkereste a service-eket. Azonban, ha a service előtti háromszögre megyek, akkor a logba ezeket írja:

  2018-10-26 12:37:58.798 subscription: 0051: "scan" subscribing to mux "634MHz", weight: 2, adapter: "Silicon Labs Si2168 #1 : DVB-T #0", network: "Mindigtv", service: "Raw PID Subscription"

  2018-10-26 12:37:58.798 mpegts: 610MHz in Mindigtv - tuning on Silicon Labs Si2168 #0 : DVB-T #0

  2018-10-26 12:37:58.798 subscription: 0052: "scan" subscribing to mux "610MHz", weight: 2, adapter: "Silicon Labs Si2168 #0 : DVB-T #0", network: "Mindigtv", service: "Raw PID Subscription"

  2018-10-26 12:37:59.854 linuxdvb: Silicon Labs Si2168 #1 : DVB-T #0 - poll TIMEOUT

  2018-10-26 12:38:03.798 mpegts: 610MHz in Mindigtv - scan no data, failed

  2018-10-26 12:38:03.798 subscription: 0052: "scan" unsubscribing

  2018-10-26 12:38:03.799 mpegts: 634MHz in Mindigtv - scan no data, failed

  2018-10-26 12:38:03.799 subscription: 0051: "scan" unsubscribing

  Ha leállítom, és W_Scan-nel próbálkozok, akkor pedig bizonyos frekvenciáknál ezt írja:

  770000: (time: 01:23.692) signal ok: QAM_AUTO f = 770000 kHz I999B8C999D999T999G999Y999 (0:0:0)
  Info: no data from PAT after 2 seconds
  deleting (QAM_AUTO f = 770000 kHz I999B8C999D999T999G999Y999 (0:0:0))

  Így összességében ez se megy.

  Dmesg pedig ezt dobja:

  [ 5.912033] em28xx 1-3:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
  [ 5.913442] tveeprom: Hauppauge model 204109, rev B3I6, serial# 14039864
  [ 5.913445] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
  [ 5.913448] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
  [ 5.913449] tveeprom: audio processor is None (idx 0)
  [ 5.913450] tveeprom: has no radio, has IR receiver, has no IR transmitter
  [ 5.913455] em28xx 1-3:1.0: dvb set to isoc mode.
  [ 5.972186] em28xx 1-3:1.0: chip ID is em28174
  [ 7.178646] em28xx 1-3:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x47e3c7c8
  [ 7.178652] em28xx 1-3:1.0: EEPROM info:
  [ 7.178657] em28xx 1-3:1.0: microcode start address = 0x0004, boot configuration = 0x01
  [ 7.185327] em28xx 1-3:1.0: AC97 audio (5 sample rates)
  [ 7.185332] em28xx 1-3:1.0: 500mA max power
  [ 7.185338] em28xx 1-3:1.0: Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
  [ 7.244083] em28xx 1-3:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
  [ 7.245678] tveeprom: Hauppauge model 204109, rev B3I6, serial# 14039864
  [ 7.245681] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
  [ 7.245684] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
  [ 7.245685] tveeprom: audio processor is None (idx 0)
  [ 7.245687] tveeprom: has no radio, has IR receiver, has no IR transmitter
  [ 7.245692] em28xx 1-3:1.0: dvb ts2 set to isoc mode.
  [ 7.444536] usbcore: registered new interface driver em28xx
  [ 7.453347] em28xx 1-3:1.0: Binding DVB extension
  [ 7.460727] i2c i2c-5: Added multiplexed i2c bus 8
  [ 7.460730] si2168 5-0064: Silicon Labs Si2168-B40 successfully identified
  [ 7.460732] si2168 5-0064: firmware version: B 4.0.2
  [ 7.463610] si2157 8-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
  [ 7.463628] dvbdev: DVB: registering new adapter (1-3:1.0)
  [ 7.463632] em28xx 1-3:1.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
  [ 7.464228] em28xx 1-3:1.0: DVB extension successfully initialized
  [ 7.464232] em28xx 1-3:1.0: Binding DVB extension
  [ 7.470257] i2c i2c-7: Added multiplexed i2c bus 9
  [ 7.470261] si2168 7-0067: Silicon Labs Si2168-B40 successfully identified
  [ 7.470262] si2168 7-0067: firmware version: B 4.0.2
  [ 7.471519] si2157 9-0063: Silicon Labs Si2147/2148/2157/2158 successfully attached
  [ 7.471535] dvbdev: DVB: registering new adapter (1-3:1.0)
  [ 7.471539] em28xx 1-3:1.0: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
  [ 7.472113] em28xx 1-3:1.0: DVB extension successfully initialized
  [ 7.472116] em28xx: Registered (Em28xx dvb Extension) extension
  [ 7.479380] em28xx 1-3:1.0: Registering input extension
  [ 7.508114] Registered IR keymap rc-hauppauge
  [ 7.508459] rc rc0: 1-3:1.0 IR as /devices/pci0000:00/0000:00:15.0/usb1/1-3/1-3:1.0/rc/rc0
  [ 7.508529] input: 1-3:1.0 IR as /devices/pci0000:00/0000:00:15.0/usb1/1-3/1-3:1.0/rc/rc0/input16
  [ 7.508801] rc rc0: lirc_dev: driver em28xx registered at minor = 0, scancode receiver, no transmitter
  [ 7.508805] em28xx 1-3:1.0: Input extension successfully initialized
  [ 7.508809] em28xx 1-3:1.0: Remote control support is not available for this card.
  [ 7.508810] em28xx: Registered (Em28xx Input Extension) extension
  [ 9.055773] r8169 0000:03:00.0 enp3s0: link up
  [ 13.157009] random: crng init done
  [ 13.157035] random: 7 urandom warning(s) missed due to ratelimiting
  [ 13.658581] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
  [ 13.659165] NFSD: starting 90-second grace period (net f0000098)
  [ 13.941912] si2168 7-0067: firmware: direct-loading firmware dvb-demod-si2168-b40-01.fw
  [ 13.941919] si2168 7-0067: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
  [ 14.233526] si2168 7-0067: firmware version: B 4.0.11
  [ 14.237658] si2157 9-0063: found a 'Silicon Labs Si2157-A30'
  [ 14.288315] si2157 9-0063: firmware version: 3.0.5
  [ 14.288339] em28xx 1-3:1.0: DVB: adapter 1 frontend 0 frequency 0 out of range (42000000..870000000)
  [ 14.301593] si2168 5-0064: firmware: direct-loading firmware dvb-demod-si2168-b40-01.fw
  [ 14.301598] si2168 5-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
  [ 14.586526] si2168 5-0064: firmware version: B 4.0.11
  [ 14.590202] si2157 8-0060: found a 'Silicon Labs Si2157-A30'
  [ 14.638817] si2157 8-0060: firmware version: 3.0.5
  [ 14.638851] em28xx 1-3:1.0: DVB: adapter 0 frontend 0 frequency 0 out of range (42000000..870000000)
  [ 24.354930] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)

  Ezek alapján olyan, mintha a FW rész rendben lenne, de aztán mégse megy a rendszer.

Új hozzászólás Aktív témák